Industry Products

VPort 351 one-channel industrial video encoder provides D1 resolution @ 30 FPS and supports a dual MJPEG4/MJPEG algorithm, making it especially well suited for use with distributed surveillance systems in critical industrial applications. It meets UL508, Class1, Div. 2, making it suitable for transportation, utility, and manufacturing systems.

Complementary to the entire family of CIP Networks, CompoNet meets the requirements of applications using large numbers of simple sensors and actuators by providing high speed communications with configuration tools and combining this with efficient construction, simple set-up and high availability – all on a single network.

Absolute SSI DuraCoder is available in either single-turn or multi-turn configurations. An optional 5/8" diameter shaft has a 100 lb radial load and a 50 lb axial load rating.

At IMHX 2007, IAS Industore will be exhibiting Hänel’s automated storage systems that have revolutionised warehousing and materials handling across the manufacturing, engineering and aerospace sectors.

The SRM7210E long-range, high speed 900 MHz radio modem has speeds of up to 800 Kbps and a range of 20 miles. Using “Wideband Frequency Hopping” technology, the modem provides data rates up to six times faster then standard Frequency Hopping technology.

ClearView meter is offered in two models: ClearView H2O for water applications and ClearView + for oils & chemicals, such as solvents and coolants. The meter is available in a variety of sizes and porting options, including NPT and BSPP in brass or polysulphone. Measuring accuracy is ±5% of full scale, with repeatability of ±1% of full scale.

SRM6310E-EU wireless Ethernet modem meets European CE Mark and ETSI RF regulations, and has Class 1 Div 2 certification.

Modular MC600 six-Channel Controller provides continuous gas monitoring when equipped with gas sensors/transmitters. It has dual redundant Modbus communications, Type 4X housing, and an optional onboard 115/230 VAC power supply that provides Class I, Division 2 classification.

TS Series Hydrogen Sulfide Gas Detectors sense H2S over a range of 0-100 ppm. The TS4000 displays H2S gas concentrations and provides complete status to the Control Room. In addition to H2S, the TS400 detects many other toxic gases.

Multi-Spectral Infrared (MSIR) FL4000 Flame Detector has been certified by Factory Mutual (FM) for application in hazardous environments.

The HazardWatch System's controller, hardware configuration and software have been tested and certified by Factory Mutual to verify NFPA 72 compliance. This includes certification for central station monitoring, as both a fire alarm panel and gas controller, for fault tolerant digital communications, and as a releasing control panel.

The wireless Wtrans T01.G1 temperature probe provides mobile and/or stationary measurement of temperature. The sensor is located in the probe grip and protected by a water-tight case. The radio frequencies used work well in an industrial environment.

VBA family of I/O modules for AS-Interface specification 3.0 is CE marked and UL listed. It supports extended addressing with 4 inputs and 4 outputs for up to 62 nodes per network.

Based on the Intel Celeron processor, the Viking III improves the speed of execution of floating point calculations, such as PID controls, Fuzzy Logic, and advanced C++ algorithms.

STAC6 220 VAC Stepper Drives provide software selectable resolutions from 200 to 51,200 steps/rev at speeds up to 50 rps. Self-Test and Auto Setup measure and configure motor parameters automatically, while anti-resonance technology eliminates midrange instability for higher motor speeds and fuller use of available torque.

Version 5.0 of ISaGRAF has been confirmed by TÜV Rheinland to be compliant with the requirements detailed in the IEC 61131-3 standard. ISaGRAF 5 incorporates both the IEC 61131-3 and IEC 61499 standards.

J Comm BCMS fits under a raised floor and monitors current, voltage, and other power related measures for up to 168 branch breakers. It helps track and control power usage in all distribution equipment.

The DNCE screw-driven linear actuator has a nonrotating round piston rod suitable for conversions from pneumatic to electromechanical automation. the DNCE is a drop-in replacement for the Festo DNC and other pneumatic cylinders based on ISO standard 6431.

PrismTech and Green Hills offer a complete Software Communications Architecture (SCA)-compliant Software Defined Radio (SDR) Operating Environment (OE) running on the INTEGRITY real-time operating system.

Profit Suite comprises advanced process control technologies that enhance the capabilities of a facility’s distributed control system (DCS). The new version increases operator effectiveness in the control room, troubleshoots a broader array of process issues, is easier to implement across third-party control systems and reduces the effort required for system maintenance.