Industry Products

“Smart Control Units” can synchronize the speeds of up to six different actuators and store frequently used positions for quick selection using only one command. These units have a standardized plug system (DIN8 for actuators and HD15 for operating devices), three or six channels for actuators, and adjustable operating parameters.

PCI-1727U analog output PCI card has 12 analog output channels with a DB-37 connector and is capable of outputting ± 10V and 0~20mA current loops with 14-bit resolution. It’s equipped with 16 TTL DI and 16 TTL DO channels that are suitable for industrial control applications and a universal PCI bus compatible with both 3.3V and 5V signaling.

Simply Modbus test tool allows technicians and system integrators to get to the bottom of MODBUS problems. The software requires little or no training. The software, which functions as a MODBUS RTU or MODBUS ASCII master, can connect directly to a slave device or remotely over a modem or radio system.

The super quiet Vortex A/C uses compressed air to cool enclosures. The noise level is 93% less than other conventional, vortex type cabinet coolers. Three models deliver 900, 1500 or 2500 BTUH of refrigeration, at a smaller size and less cost as an air conditioner.

CmX Series connector features a simplified connection design that replaces conventional circular connectors. The low-profile connectors are 50 percent smaller and lighter than conventional circular connector designs with significantly lower installation costs.

The C9900-F212 and C9900-F214 are stainless steel front plates that protect the C36xx PC from airborne water particles, are IP65-rated, and provide greater application flexibility. This enhancement is ideal for market segments such as packaging, food and beverage production and water treatment.

The ChekVolt interface, installed on an electrical panel, allows maintenance personnel to use a non-contact voltage detector ‘pen’ to check line voltage before and after they open the main disconnect. The ability to pre-verify electrical isolation before opening a panel puts an additional safety measure between electricians and hazardous voltage.

These sensors are designed to measure rotating drive torque using a conventional shaft-to-shaft configuration for in-line placement. The design incorporates a digital non-contact wireless system that provides power to the rotating electronics mounted on the shaft and transmits the signal back to the receiver in digital format.

SeaI/O-520 digital I/O module includes a combination of high-current Form C outputs and optically isolated inputs. It provides eight SPDT relays that can directly switch up to 6A loads at 250VAC and 100VDC. Eight non-polarized inputs can monitor 5-30VDC.

Using a simple USB connection and programming software, DRS61 60mm diameter incremental encoders empower customers to freely program the number of lines from 1 to 8,192, as well as the width of the zero pulse. This flexible programmability allows users to use a single type of encoder that can be programmed at any time, in any location, for any application.

Universal Positioning System lets users position and lock items in any plane. It can be equipped with ball-end mounts or V-block clamps for securely holding video cameras, sensors, and other devices. Ideally suited for use on conveyors and packaging equipment, it provides unlimited degrees of positioning freedom and is very rigid and stable once locked in place.

The 4BKR media-separated solenoid valve controls the flow of either ultra pure or corrosive media preventing premature failure on wetted type solenoid valves. This 2 way, 2 position unit has a low volume valve cavity and rolling diaphragm and won't allow chemicals to gather or dead spots to form which might hinder flow.

Zlinx wireless remote I/O maps directly into a Modbus table, making it an easy fit to any PLC, HMI or PC based control system running LabVIEW or other popular automation software. Wireless modules provide Modbus compatible communication at ranges up to 20 miles.

A smart AC motor drive allowed Centrilift Cable to eliminate a PLC and improve the productivity of winding finished cable onto drums at its facility in Claremore, Oklahoma. Centrilift Cable makes specialized cabling for the electrical submersible pumping systems used in oil and gas wells.

KPXI products are for high speed automated production testing as part of a hybrid test system using precision instruments. Test engineers and designers can combine high-speed data acquisition and tight trigger synchronization of the KPXI products with the precision measurement capabilities in Keithley instruments for a hybrid test system architecture.

JetCon 2401 RS232/422/485 to fiber converter transmits serial protocol over fiber media up to 40km (JetCon 2401-s single-mode) or up to 5km (JetCon 2401-m multi-mode) and provides a higher level of signal quality and security than copper cabling. A fiber optic network link is immune to EMI, RFI, cross-talk, ground loops and other electrical problems, greatly enhancing the signal quality in severe environments.

The ET-10MG offers 8 10/100 Mbps RJ45 ports plus 2 Gigabit combination ports for copper or fiber connections. All of the RJ45 copper ports support auto-negotiating (10/100 or 10/100/1000), auto-crossover and auto-polarity for plug & play connections. The fiber ports 9 & 10 also accept SFP fiber optic transceivers for noise immune links up to 80 km.

InternalWeb DV server software resides within an AXT100 fixed-mount thermal imaging camera and interacts with it, similar to a router's internal web page. Using the server, the AXT100 can connect to a network with Fast Ethernet and stream live video or thermal data to multiple destinations.

D-EPIC control transmitter provides a cost-effective alternative to positioners for Safety Instrumented System (SIS) applications. Exida confirmed the D-EPIC is suitable for Safety Integrity Level 3 (SIL3) service by performing a FMEDA with calculated PFD and SFF values.

Multifunction data acquisition (DAQ) modules and instrument chassis offer increased bandwidth for multiple I/O operations, ease of connectivity, hot-swappable connections, and a sampling rate of up to 3 MSa/sec for a single channel. Users can set up and configure tests swiftly with its plug-and-play USB interface.