Industry Products

Precision Sleeve Coupling has a solid center section that provides a close tolerance fit on ground shafting, incorporates integral self-centering clamping collars at both ends and maintains 0.001 TIR concentricity while in use to assure precise shaft alignment.

JAP100 Cylinder-Integrated Diaphragm Chuck has a built-in air cylinder, repeatability of 0.00004” (0.001mm), and makes it easy to set up a precise chucking system.

SPH613 and SPH1013 series power supplies for 600 and 1,000 watts, respectively, require an installation width of only 56 mm for 600 W and 66 mm for 1,000 W. These power supplies can be used for a full range of industrial applications, offer flexible fixings (DIN-rail or wall mounting) and operate in any position at temperatures of up to +70° C.

FactoryPMI web-based SCADA system now has a plug-in that produces PDF based reports without the cost of individual client licenses or the need to physically install client software at each workstation.

RJFast converts a standard RJ-45 cable into a category 6 Ethernet connector compatible with industrial environments (including IP67) in a few seconds, without tedious, long and costly crimping.

ALAR series direct-drive rotary stages provide angular positioning and velocity control with exceptionally large apertures, load capability, and very high speeds. With the combination of a large aperture and direct-drive motor, the ALAR series offers significant performance benefits compared to worm-drive large aperture stages.

Panther terminals now have Device Net. These terminals can be integrated with process control equipment through a variety of methods, including Discrete I/O, 4-20 mA or 0-10 V analog output, Allen Bradley RIO, Modbus Plus, PROFIBUS and the newly integrated DeviceNet.

IND780 terminal comes standard with Ethernet, two serial ports and a USB master for an external keyboard. The terminal is capable of simultaneously supporting four scales and can provide a metrologically approved sum scale.

IND690 application terminal withstands all industrial environments whether the challenge comes from aggressive weighing samples, cleaning agents or a wet, corrosive, or dusty environment. It can connect up to four scales with a sum scale including any of these weighing technologies: analog load cells, high precision bases, analytical balances and BBK four-series scales.

Tru-Vue series photoelectric sensors are now available with 4-in-1 outputs. This enables a single sensor to operate in NPN normally open, NPN normally closed, PNP normally open, or PNP normally closed configurations. 4-in-1 simplifies sensor selection and stocking because one sensor model can now replace four sensor models.

The new interface provides flexibility for users performing standard weighing, blending or filling or checkweighing applications to interface with their DeviceNet network without the need for an external device. The IND560 built-in target controls can be used to create hybrid automated control systems for process and filling applications.

The Automated Precision Weighing Weigh Modules (WM and WMH) have RS232, RS422, DeviceNet, Profibus DP and Ethernet intefaces. The two products feature readability of up to 0.1mg with capacities of up to several tons. They are all available as intrinsically safe versions for integration in hazardous areas.

DT10, DT20, DMT10-2 and DML40-2 Distance Measurement Sensors allow customers to upgrade from simple detection to measurement applications where previously space and budget made it prohibitive.

Surge protection and wiring device products include surge panels, plugs, connectors and receptacles. 74000 and 75000 Series Surge Panels designed for facilities with 3-phase WYE-configured (4-wire + ground) systems where surge protection for all seven modes in the AC distribution network is required. Industrial Grade Black and White Locking Plugs and Connectors are available in 15, 20 and 30 Amp versions.

WebPort 2005 and WebPort 4005 industrial Ethernet gateway modules securely link serial devices or PLCs to an Ethernet LAN, allowing data access from any workstation. It connects up to four Ethernet-enabled control devices, offers serial connectivity to another controller, a modem for remote maintenance, and a WAN Ethernet port for connecting to the Internet or any IP network.

FieldPort FPIO-I8H-EIP and FPIO-I8H-EIP modules provide full analog capability, HART (Highway Addressable Remote Transducer) protocol, Ethernet-IP and ModbusTCP system interfaces, and work with Rockwell Automation and Schneider Electric Legacy PLCs.

Active Sensor Actuator Interfaces (SAIs) provide users with greater levels of wiring flexibility for achieving modular and decentralized process control in automation applications. The Active SAIs are available in IP 67 housings and support all industry network protocols including Profibus, DeviceNet and CANopen, as well as Ethernet, Ethernet/IP, PROFINET and Modbus/TCP.

The PCI-1625U is a self-contained computer with an onboard DSP processor that will take over the processing load from the host PC. It is designed for industrial applications where a PC needs to communicate with terminals, modems, or other instruments. A user can install up to four cards for total of 32 ports in any PCI bus-based PC.

DataBus IndustrialTuff PROFIBUS DP and PA shielded twisted pair cables deliver high performance and reliability in PROFIBUS factory automation and process automation applications. Cables are available with a selection of special jacket compounds, cable colors, and armoring options to fit application requirements.

TiR Series IR imagers help expert users accurately pinpoint building problems by combining both visible light and thermal images for better identification, analysis and image management. It has a 20 mm germanium lens on a 180 degree articulating mount to view images, even in situations where access is limited.